Tag: IEEE

How To Choose And Set Wireless Network Card On Dm800 Hd Receiver

The DM800 support the wireless card with a USB interface, it can be connected in LAN via wireless. Two accessories should be available when using the wireless network card: one is an AP, we choose TP-LINK WR541G to make up the wireless local area network; the other one is USB wireless card which can be compatible with DM800. Here will introduce how to choose and how to set his wireless network card on DM800.

How to choose the wireless network card
The most important for choosing a WLAN card is to balance cost and quality. You must ensure the WLAN card can work well with your DM800 and owning enough functions to meet what you request. In the example, we choose the TP-WIN321G made by TP-LINK which is a 54M wireless USB network card and compliable with IEEE 802.11b and IEEE 802.11g standers. The parameters are listed above would be considered when you buy one WLAN card.
How to set the WLAN card
Before you set WLAN card, you should insert Tl-WN312G card into the USB interface on the bake plane of DM800. Then switch the power. The follow is the specific steps to set the WLAN card.
1. First ,fromMain Menu blue panel set into kernel module interface. Select WLAN RT73 to yes the TL-WN321G the RT2571WF chip RT73 drivers, so select “WLAN RT73” to “Yes”, then press Green key to save. The system will load the needed documents.

2. After loading is complete, from the menu set System to enter the network configurationinterface, select to restart the network.

3. After restart, once again return tonetwork configuration interface, and select the card will appear, press OK key to enter.

4. the screen will appearweb configurationinterface, select option scanto scan the WLAN. The available wireless networks will display under Choose a Wireless Network , choose one for DM800.

5. According to the information provided by the wireless network interface ,press the green button to enter the set.Wireless card setting up method is the same as the built-in integrated network card.

6. After setting, press OK to active the settings. Soon later, it will pop up item that second NIC is disable? that is ask you whether forbidden the network card inside the machine, usually select yes.

Linksys Wireless Bridge Wet610n

WET610N is a dual-band wireless Ethernet bridge based on IEEE 802.11n draft 2.0 and optimized for video transmission. WET610N can operate in either 2.4GHz or 5.0GHz radio bands (selectable dual-band), and it is fully backward compatible with widely deployed 802.11a/b/g infrastructure, 1-Port 10/100 Mbps half or full-duplex modes, auto-sensing, integrated QoS features.
The IP Address is set to DHCP, if you have a router or DHCP server check the DHCP Clients table for address. If there is no DHCP Server detected the Bridge will default to the IP address 169.254.1.250.
WET610N does not have default IP address. It will pick up one from the router or DHCP server.
You should know the wireless settings of your network.
If your wireless network is secured then make sure that you have the correct wireless network key/password.
How to setup WET610N:
Connect WET610n to the router with the Ethernet cable.
Open the setup page of your wireless router and go to the DHCP client table list. In this list you will find the devices connected to your network. You will find the IP address of the bridge. Note down that number.
Open the Internet browser and in the address bar type the IP address of the bridge. It will open the setup page of the bridge.
Click on Wireless tab and go to Wireless Network site survey. Select your wireless network from the list and try to connect. If it is a secured wireless network then enter the password of your wireless network. It will connect to the network.
Now disconnect the Ethernet cable from the bridge and power cycle it. Now try to ping the IP address of the WET610N.
If you are not able to find IP address of your bridge in the DHCP client table of your router then you can try another way to access the setup page.
Connect WET610N to the Ethernet port on your computer. Press and hold the reset button for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle it.
Now open the Internet browser on your computer and in the address bat type 169.254.1.250. Log on to the setup page and try to connect to the wireless network.
Once the wireless bridge is configured successfully, you can connect it to the device that you want to use in the network. You can use it with special devices like Play station, BluRay player or Xbox also. If you have more that one devices that you want to use it wirelessly then you can connect the bridge to a switch and connect all the devices to the switch. In this way you can connect multiple devices to the wireless network using only one wireless bridge.